We’re within the midst of slightly laundry room refresh and I’ve been slowly finishing tasks to replace this house. We completed it virtually 7 years in the past and it’s probably the most used rooms in our house (after the kitchen). However now that we now have 3 kiddos and my type has developed it’s time for some modifications! My most up-to-date challenge was constructing a shelf with a wooden gallery rail and I’m right here to share all the main points with you!
After we first accomplished the laundry room, we put a shelf on the wall above the washer and dryer that was round 5′ lengthy. I don’t know why I made a decision on that size or why I didn’t prolong all of it the best way throughout the wall. It was early in my design journey and the laundry room was the primary room I ever designed from high to backside!
The extra I checked out it, it simply appeared unbalanced and there was extra room for extra storage and performance. So I got here up with the concept to create a shelf with a wooden gallery rail on high and a dangling brass rail on the underside.
I used to be impressed to create the wooden gallery rail after making a pet food holder for Oakley out of bigger wooden spindles. Brass gallery rails have change into tremendous standard in design – we now have one in our kitchen and I adore it – however I needed to place a special spin on it. A number of older antiques have this aspect which is such a phenomenal element, and I needed to do it in a extra trendy manner that match my type higher.
SUPPLIES FOR SHELF WITH A WOOD GALLERY RAIL
STEP 1
Drill the holes on your finials. You’ll wish to measure out your spacing first – I spaced mine 2.5″ aside from each other however you are able to do no matter appears greatest to you! I positioned them about 1/2″ from the entrance fringe of the board.
To drill the holes I used a 5/8″ drill bit. You might additionally use a spade bit however since these have a sharp finish, I didn’t wish to threat drilling by way of the wooden!
STEP 2
Trim the highest a part of the finials off. It was pretty straightforward to drill into the shelf board, however drilling into the nook spherical can be actually difficult. So to keep away from this, I simply trimmed off the highest a part of the finials in order that the nook spherical might sit flat.
I used the band noticed to do that and it was so fast and straightforward! If wanted, you may then sand down the tops for a very clean floor.
STEP 3
Minimize and miter your nook spherical. It helps to position your finials within the holes to get a greater thought of the place the nook spherical will sit. Then you need to use your mitre noticed set at a forty five° to chop every bit.
STEP 4
Drill the holes in your corbels. When you’ve got a drill press that’s the best manner to do that, however we don’t so I used some clamps and my common drill. The copper pipe I used for the “brass rail” is 1/2″ and I used a 5/16 spade bit for the holes.
I stained my corbels first, however I recommend drilling first after which staining!
Begin by clamping two corbels collectively. Be sure they’re aligned the correct manner (ie. the brackets on the again are dealing with the identical manner). Eye ball the middle space of your corbel the place you need the pipe to go and drill down as straight as you may by way of each corbels.
When you’ve completed the primary two, take one in all them and place it on high of a non drilled corbel. Use this as a template to drill into the one beneath. Repeat till all corbels have been drilled by way of.
STEP 5
Now that every one your wooden is minimize and prepared it’s time to stain. I used a wooden conditioner first which helps to get rid of splotching and provides you a pleasant even end. You’ll be able to apply this with a black foam brush.
Then I used my favourite Darkish Walnut Gel Stain to stain every little thing. I used a staining pad for the precise shelf and corbels after which used a small craft paint brush for the finials. Then I wiped the finials off on a rag to take away the surplus.
STEP 6
As soon as the stain is dry, apply a high coat. I used Basic Finishes Excessive Efficiency High Coat in Satin and solely did one coat since this isn’t going to get a whole lot of motion 😉
STEP 7
Minimize your copper pipe. Earlier than you chop, measure out the size you want by inserting the 2 finish corbels on the wall. This will provide you with a extra exact measurement however you do have some wiggle room because the pipe will sit an inch or so into the corbels.
We determined to have the pipe go right through all 5 corbels in a single piece however you could possibly additionally minimize the pipe into sections and have the seams be hidden throughout the corbels.
Chopping copper pipe is tremendous straightforward with this little pipe cutter you may get on the house enchancment retailer.
STEP 8
Spray paint your pipe. I used this gold leaf spray paint after which this clear coat on high of that.
STEP 9
Create your wooden gallery rail! Glue your finials into the holes you drilled after which glue the nook spherical on high. This DAP Speedy Fuse glue is my favourite. It dries tremendous fast and is so sturdy!
STEP 10
Grasp your shelf! Pull the pipe by way of the corbels and hook the corbels onto the screws within the wall. We had been in a position to make use of a few of the present holes that had been there already after which needed to drill new holes on both finish. To drill into tile, simply ensure you use a masonry bit!
We had slightly hassle getting all 5 corbels to slip into BOTH screws for every one so we ended up solely utilizing one screw per corbel and it was nonetheless tremendous sturdy.
STEP 11
Spray paint your hooks to match the pipe. No matter colour you spray your pipe, ensure you use the identical on your hooks in the event that they aren’t match. I used these bathe hooks and love the little ball element they’ve.
Now it’s the enjoyable half – time to brighten and luxuriate in your shelf!
This wooden gallery rail shelf feels SO significantly better than the unique one did on this house. I like that it fills up the entire size of the wall and has the extra brass rail beneath to hold issues from. It’s additionally lots prettier and added a beautiful contact of allure and character to our laundry room.
What do you assume? Would you construct your individual shelf with a wooden gallery rail?
Associated
